Genie of Fairview Wireless Keypad Model GPWK-12, GWK

This keypad works with remotes having either 9 or 12 internal code setting switches and 390 frequency. The keypad is black with a slide-up cover showing the Genie logo only. Notice the star and # switches.

This keypad is NOT compatible with Genie of Fairview Intellicode remotes. If your keypad looks like this but has Intellicode on the cover go to the next set of programming instructions below.

Step-By-Step Programming Instructions

1. Reset keypad by sliding the cover half way up. While holding down on the # and 8 keys at the same time slide the cover up the rest of the way until it clicks or latches. Release the # and 8 keys. Close the cover.
2. Open the cover back up and press in order the 3, 5, 7 and # keys.
3. Enter your PIN of your choice and press the # button. Your PIN can be up to 8 digits. Do not use the # or star key.
4. Enter the Door Code determined by Chart A below and this time press the Star (*) key.
5. Slide keypad cover down.
6. Test keypad by sliding the cover up until it latches. Enter your PIN and press the Star (*) key. Your door should operate.

The Door Code in step 4 above is determined by the internal code switches inside one of your remotes. Look at the first 3 switches and determine which ones are up and which are down. Look at the chart below and write down the corresponding Door Code Number. Look at the next 3 switches and determine its code number. Continue until you have 4 Door Code numbers for a 12 switch remote, or 3 Door Code numbers for a 9 switch remote.

Genie Wireless Intellicode Keyless Entry Pad Programming

3 Models were made for Intellicode remotes, shown here from the oldest to the newest.

Model 1: Intellicode Models GWKIC, ACSDG ( black with slide-up cover and the work “Intellicode” printed on the cover.

Two Part, Step-By-Step Programming.

Part 1
To Reset your Genie of Fairview Intellicode Wireless Keypad follow these steps

1. Open cover half way.
2. Press and hold both the “PROG” and “8” keys and open the cover until it latches. (the indicator light on the keypad will blink one and go out)
3. Close cover.

Programming your Intellicode keypad

1. Open cover fully until it latches.
2. Press in order 3 – 5 – 7.
3. Press the PROG key. (red light blinks)
4. Enter the Personal Identification number (PIN) of your choice.
5. Press the PROG key. (red light blinks twice as fast – this tells you it took your PIN)
6. Close cover fully and Proceed to Part 2.

Part 2
Gently press and release the radio receiver Learn Code button on the motor head in your garage to start the red indicator light next to the button will start blinking. This small black button is always found near the floppy antenna wire and is usually behind the light cover for your light bulbs.
While the indicator light is blinking enter your PIN number and Press the SEND button several times ( 3 or 4 ) until the door is activated.

Model 2: Intellicode Model GWKP
(off-white with flip-up cover – program key above the 3 key)

1. To erase the old PIN (Personal Idendification Code) press and hold down, in order, the PROGRAM , 6 and UP/Down Arrow keys. The red light on the keypad will blink once and turn off. Release the buttons.
2. To program a new code press and let go in order the 3, 5, 7 and PROGRAM keys.
3. Enter your chosen PIN, anywhere from 3 to 8 numbers and press PROGRAM (the red light should blink twice as fast and turns off, indicating it took your code)

Once you’ve set the keypad code go to your Genie of Fairview motor head follow the instructions below:

Gently press and release the radio receiver Learn Code button on the motor head in your garage to start the red indicator light next to the button will start blinking. This small black button is always found near the floppy antenna wire and is usually behind the light cover for your light bulbs.

While the indicator light is blinking enter your PIN number and Press the UP/DOWN arrow button several times ( 3 or 4 ) until the door is activated.

Model 3: Programming instructions for your Genie of Fairview GK-BX Wireless Intellicode Keypad.
(this keypad is off-white with a flip-up cover and the PROGRAM key is above the 2 key)

Gently press and release the radio receiver Learn Code button on the motor head in your garage to start the red indicator light next to the button will start blinking. This small black button is always found near the floppy antenna wire and is usually behind the light cover for your light bulbs.

While the indicator light is blinking enter your PIN number and Press the SEND button several times ( 3 or 4 ) until the door is activated.

To clear out the factory settings or the previous code, press and hold both the PROGRAM key and the Up/Down arrow keys until the red light on the keypad flashes twice and goes out.

1. Press and let go in order the 3, 5, 7 and PROGRAM keys
2. Enter the PIN of your choice (3 to 8 numbers) and press PROGRAM.
3. This sets the code for your keypad. Now follow the instructions below to link your keypad to your Genie of Fairview Door opener.

Gently press and release the radio receiver Learn Code button on the motor head in your garage to start the red indicator light next to the button will start blinking. This small black button is always found near the floppy antenna wire and is usually behind the light cover for your light bulbs.

While the indicator light is blinking enter your PIN number and Press the UP/DOWN arrow button several times ( 3 or 4 ) until the door is activated.

Note: Once your keypad is programmed to your garage door opener, chaning your PIN to another code is easy. Just enter your present PIN and hit the PROGRAM key, then enter a new PIN and press PROGRAM. Wait for the backlight to go out and test. The keypad should now be set to the new PIN

Programming your GK-BX for the newest line of Genie garage door openers. These include the Genie InelliG, TriloG, SilentMax, PwerMax, GPower, and PowerLift Series Openers (Intellicode II).

These include models 4024, 3024, 4042, 3042, 4022, 3022, and 4046, 3064, 4062, 3062, 2564, 2562. Looking up at the bottom of the Genie motor head cover in your garage you will see a set of black buttons depicted in the drawing below along with two LED lights shown here in grey.

1. Press and let go in order the 3, 5, 7 and PROGRAM keys
2. Enter the PIN of your choice (3 to 8 numbers) and press PROGRAM.
3. Press and hold the square Program button (shown on the diagram above, located on the bottom outside cover of your Genie of Fairview motor head) until the round blue LED light comes on and let go.
4. Upon releasing the square button the round blue light should switch to the long purple light and begin to blink. **
5. While the purple light is blinking go to the keypad and enter your programmed PIN and press the Up/Down arrow key 3 or 4 times, until the door activates.

** If after performing Step 4 above and releasing the square button, the round LED comes on and stays blue, follow the instructions below:

1. After step 4 above the short LED light should be a steady blue. Press the square button once and the short blue light will switch to the long LED and blink Purple.
2. Unlock the programming feature on your garage door opener by using one of your existing remotes and pressing it only once.
3. While the purple light is blinking go to the keypad and enter your programmed PIN and press the Up/Down arrow key 3 or 4 times, until the door activates.

Programming Genie Hardwired Keyless Entry Pad (KEP1).
(This keypad has no cover and is connected to the inside receiver by the special ribbon attached to the keypad)

The outside garage door opener keypad has a flat ribbon, which slides behind the garage door molding into the garage and attaches to the keyless entry receiver box. Behind the receiver’s cover is a switch.

Slide the switch to SET, enter your PIN of your choice followed by the “star” key. Slide the receiver switch back to RUN. Test the keypad by entering your PIN and hitting the “star” key.

Programming DOMINO Hardwired Keypads

1. Slide switch on the receiver box on the inside of the garage to Program.
2. Press the ENTER key, then enter the personal code of your choice (up to 6 digits) and press ENTER again.
3. Slide the switch on the box in the garage to OPERATE. Test keypad.